This SurgeX SEQ Programmable Sequencer Surge Eliminator, 2U, 120V/20A provide the sequencing parameters, conditioning, shutdown thresholds, and surge protection.
The SurgeX SEQ SEQUENCERS provide guaranteed surge protection, power conditioning and sequencing for audio, video, broadcast and computer equipment.
When electronic equipment must be powered up or down in order, rather than simultaneously, sequencing is needed. In AV systems, sequencing is often necessary for controlling power distribution to avoid pops and hissing sounds, along with excessive inrush surge currents that can trip circuits.
SurgeX Sequencers extensive management features give the parameters, and adjustable shutdown thresholds needed to properly sequence power and enhance AV performance. They are controlled from the front panel or remote locations, include a built in AC voltmeter, an override input to force the unit on or off can be programmed to restore power or remain off after a power failure, and can be password protected for enhanced security.
Featuring Advanced Series Mode power protection and conditioning, the Sequencers safeguard connected equipment from the harmful surges, spikes, electrical transients, and noise that can affect AV performance and cause equipment downtime. It is the only technology that eliminates surge energy up to 6,000 Volts and will not produce ground contamination or common-mode disturbances.
SurgeX SEQ Programmable Sequencer Surge Eliminator, 2U, 120V/20A Features:
- Three sequenced banks of four receptacles; two always-on receptacles
- Setup stored in non-volatile memory
- Can control other SurgeX products or daisy-chained with other SEQ sequencers (SEQ)
- LCD screen (SEQ)
- Magnetic shielding steel enclosure
- 9' grounded 3-wire cord
- SEQ Programmable Sequencer Surge Eliminator, 2U, 120V/20A
- Advanced Series Mode surge protection
- Three sequenced banks of four receptacles; two always-on receptacles
- Setup stored in nonvolatile memory
- Impedance Tolerant EMI/RFI filtering
- Over/Under Voltage Shutdown
- Inrush Current Elimination
- Can be used to control other SurgeX products or daisy-chained with other SEQ sequencers (SEQ)
- LCD screen (SEQ)
Why not buy this SurgeX SEQ Programmable Sequencer Surge Eliminator, 2U, 120V/20A today?
SurgeX SEQ Programmable Sequencer Surge Eliminator, 2U, 120V/20A Specifications:
- Load Rating: 20 amps @ 120 volts.
- Power Requirement (no load): 20 watts.
- Surge Let-Through Voltage (6000-volt surge): 0 volts
- UL 1449 Adjunct Classification Test Results: 1000 surges, 6000 volts, 3000 amps, B3 pulse;
- Measured suppressed voltage: 170 volts; no failures
- Federal Guidelines: Grade A, Class 1, Mode 1 (CID A-A-55818)
- EMI/RFI Filter, Normal Mode (50-ohm load):
- 40 dB @ 100 kHz; 50 dB @ 300 kHz;
- 50 dB @ 3 MHz; 50dB @ 30 MHz
- EMI/RFI Filter, Common Mode (50-ohm load):
- 18 dB @ 300 kHz; 30 dB @ 1 MHz;
- 50 dB @ 5 MHz; 50 dB @ 20 MHz
- Maximum Applied Surge Voltage: 6000 volts*
- Maximum Applied Surge Current: Unlimited, due to current limiting*
- Maximum Applied Surge Energy: Unlimited, due to current limiting*
- Endurance (C62.41-1991 Category B3 pulses): 1 kV>500,000; 3 kV>10,000; 6 kV>1000
- Control Inputs: Momentary Switch, Latching Switch,Contact Closure or 5-30 Vdc
- Input Control Current: 3 mA
- DC Voltage Output: 12 Vdc, 40 mA maximum load
- Auxiliary Relay Output: 1 amp, 30 Vdc
- Delay Times: 0-40 seconds
- Dimensions: 3.5" H x 19.0" W x 10.5" D (8.9 x 48.3 x 26.7 cm)
- Weight: 16 lbs (7.3 kg)
- Temperature Range: 5§ to 35§ C
- Humidity Range: 5% to 95% R.H., non-condensing.
- Agency Listings: ETL and cETL (UL 1449, 2nd edition; CSA C22.2 No.8-M1986, R2000)
*1.2 x 50 æs pulse, industry standard combination wave surge, as per IEEE C62.41
