This NTI ST-IPFOHD-R-LC-ULC Low-Cost HDMI Extender Over IP via One LC Singlemode/Multimode Fiber Optic Cable - Remote Unit transmits digital video, embedded audio, and IR signals up to 24.8 miles (40 kilometers) away from an HDMI source using a single LC singlemode fiber optic strand or 984 feet (300 meters) using OM3 LC multimode fiber optic cable.
Each HDMI Extender Over IP consists of a local unit that connects to an HDMI source and also supplies video to a local monitor, and a remote unit that connects to an HDMI display. The local and remote units can be connected together for a Point-to-Point connection via Fiber Optic Cable or a Point-to-Many connection via a network switch. Support for multiple transmitters requires a managed network switch
NTI ST-IPFOHD-R-LC-ULC Low-Cost HDMI Extender Over IP via One LC Singlemode/Multimode Fiber Optic Cable - Remote Unit Features:
- Signal transmission via single-strand LC fiber optic cable.
- Using singlemode 9-micron cable, extend to 24.8 miles (40 km).
- Using 50-micron OM3 (or better) multimode cable, extend to 984 feet (300 meters).
- Supports HDTV resolutions to 1080p.
- Cascade network switches to extend the length longer distances.
- Up to three switches can be cascaded.
- HDMI features supported:
- HDMI 1.3
- 36-bit Deep Color
- RGB, YCbCr 4:4:4, and YCbCr 4:2:2
- LPCM
- Bandwidth up to 4.46 Gbps
- HDCP 1.4 compliant.
- Full Infrared Remote (IR) control of HDMI source from remote HDTV using existing source remote control.
- For a point-to-many connection, a standalone network with an unmanaged SFP network switch, hub, or router can be used instead of a managed SFP network switch.
- Easily expandable. Add remote units as you add monitors.
- Up to 253 receivers supported.
- It is not recommended to use any other network devices on this standalone network as it may cause degradation in performance.
- Easily expandable. Add remote units as you add monitors.
- Support for multiple transmitters (many-to-many connection) requires a managed SFP switch with VLAN support. Standard LAN switches can only support one transmitter.
- The managed SFP switch must support port-based IEEE 802.1Q VLAN.
- Each VLAN acts as a separate HDMI Over IP Channel on the network.
- Each VLAN channel supports one transmitter.
- Number of local and remote units that can be used is dependent on the backplane bandwidth of the switch.
- Plug and play installation allows receivers to find the transmitters automatically on the same subnet.
- Local and remote units must be in the same LAN. The units do not support WAN connections.
- Buffered HDMI input loop-through.
- Low RFI/EMI for sensitive applications.
- Built-in default EDID table.
- Cables can be installed in conduit prior to extender installation.
- Integrated mounting brackets for easy surface/wall mounting
Why not buy this NTI ST-IPFOHD-R-LC-ULC Low-Cost HDMI Extender Over IP via One LC Singlemode/Multimode Fiber Optic Cable - Remote Unit today?
NTI ST-IPFOHD-R-LC-ULC Low-Cost HDMI Extender Over IP via One LC Singlemode/Multimode Fiber Optic Cable - Remote Unit Specifications:
Local Unit
- One female HDMI connector for source connection.
- One female HDMI connector for local monitor.
- Supports HDTV resolutions to 1080p @60Hz.
- One 3.5mm port for IR emitter (included).
- IR frequency range: 20 to 60 kHz.
- One simplex LC fiber optic port for sending/receiving video/audio and IR signals.
- Supports HDCP 1.4.
Remote Unit
- One female HDMI connector for monitor.
- Supports HDTV resolutions to 1080p @60Hz.
- One 3.5mm port for IR receiver (included).
- IR frequency range: 20 to 60 kHz.
- One simplex LC fiber optic port for sending/receiving video/audio and IR signals.
- Encoding delay: 100 ms latency
- Supports HDCP 1.4.
Power
- Local and remote unit:
- Input: 100 to 240 VAC at 50 or 60Hz via AC adapter. (Country-specific power supplies included.)
- Output:
- US power supply: 5VDC, 2A
- UK, EU, AUS power supplies: 5VDC, 3A
- Power consumption: 3W each.
Environmental
- Operating temperature: -4 to 140°F (-20 to 60°C).
- Storage temperature: 22 to 158°F (-30 to 70°C).
- Operating relative humidity: 0 to 90% non-condensing RH.
Dimensions
- WxDxH (in): 5.43x3.21x0.94 (138x82x24 mm)
Max Distance
- 24.8 miles (40 km) over 9μm singlemode LC fiber optic cable.
- 984 feet (300 meters) over 50μm OM3 (or better) multimode LC fiber optic cable.
Cables
- Use a simplex LC singlemode 9-micron fiber optic cable to extend the receiver from the transmitter up to 24.8 miles (40 km).
- Use FIBER-AD-SS-SCFLCM to convert a male simplex SC singlemode connector to a male simplex LC singlemode connector.
- Use a simplex LC multimode 50-micron OM3 (or better) fiber optic cable to extend the receiver from the transmitter up to 984 feet (300 meters).
- Use HD-xx-MM cables to connect an HDMI source or display up to 50 feet.
- Use DP-HD-xx-MM cables to connect a DisplayPort source up to 15 feet.
- Use DVI-HD-xM-MM cables to connect a DVI source up to 5 meters.
- Use USB3C-HD4K-xx-MM to connect a USB-C or Thunderbolt 3 device up to 10 feet.
- Cables not included.
Regulatory Approvals
- CE, FCC, RoHS
Warranty
- Two years.
Package Includes
- One transmitter unit
- One receiver unit
- One T1550/R1310nm 1000 Base-T Gigabit SFP module
- One T1310/R1550nm 1000 Base-T Gigabit SFP module
- One IR emitter
- One IR receiver
- Two power supplies
Why not buy this NTI ST-IPFOHD-R-LC-ULC Low-Cost HDMI Extender Over IP via One LC Singlemode/Multimode Fiber Optic Cable - Remote Unit today?
NTI ST-IPFOHD-R-LC-ULC User Manual
NTI ST-IPFOHD-R-LC-ULC Datasheet
Why not buy this NTI ST-IPFOHD-R-LC-ULC Low-Cost HDMI Extender Over IP via One LC Singlemode/Multimode Fiber Optic Cable - Remote Unit today?
Reasons To Buy an NTI Product