This JVC FS-900CAM1N MultiDyne Camera Back Fiber Transceiver with Neutrik opticalCON Connector is a new camera mounted Fiber optic system designed for JVC's GY-HM890 ProHD camcorder. Built exclusively for JVC by MultiDyne Video & Fiber-Optic Systems, the system supports 3G-SDI 1080p/60 camera feeds and returns and takes advantage of the camera's built-in streaming engine for video-over-IP functionality. The camera module connects directly to the back of GY-HM890 camcorder via 68-pin interface - no external cables required - for full studio functionality. It transports multiple bi-directional 3G-SDI signals as well as control, audio, sync and intercom between the camera and the FS-900 Base Station.
Up to three cameras are supported by the Base Station and its redundant power supplies provide up to 150 watts for each camera, as well as prompters and talent monitors. Its three-in-one configuration provides a more cost efficient solution than other multi-camera solutions previously offered by JVC and other manufacturers.
With built-in gigabit Ethernet, the lightweight, 2 RU Base Station also allows video-over-IP, control and advanced configuration. The high quality 1080p video signals are ideal for webcasts, virtual sets and image magnification (I-MAG) applications. The system integrates easily with any studio, mobile truck or portable flypack and connects directly with a facility's switcher, router, intercom and house sync systems.
JVC FS-900CAM1N MultiDyne Camera Back Fiber Transceiver with Neutrik opticalCON Connector Features:
- Cost-efficient three-camera studio configuration with single base station
- Supports 1080 50/60p 3G-SDI camera feed and returns
- Camera adapter design allows to use VF-HP790 or generic SDI monitors as studio VF
- HDMI / SDI feeds for high-quality HD teleprompters
- Gigabit Ethernet for Video-over-IP and web-based RCU
- Dual redundant power supplies
Why not buy this JVC FS-900CAM1N MultiDyne Camera Back Fiber Transceiver with Neutrik opticalCON Connector today?
JVC FS-900CAM1N MultiDyne Camera Back Fiber Transceiver with Neutrik opticalCON Connector Specifications:
Digital Video, Camera to Base
- Number of Channels: 1 Per Camera
- Interface: SMPTE ST259, ST292, ST424
- Data Rate: 270Mbps, 1.5Gbps, 3Gbps
- Input/Output Leve: l800mVp-p
- Input/Output Impedance: 75Ohms
- Number of Outputs at Base: 2 Per Camera
Digital Video, Base to Camera
- Number of Channels: 3 Per Camera
- Interface: SMPTE ST259, ST292, ST424, HDMI
- Data Rate: 270Mbps, 1.5Gbps, 3Gbps
- Input/Output Leve: l800mVp-p
- Input/Output Impedance: 75Ohms
- Connectors: BNC, HDMI
Video, Genlock
- Number of Inputs: 1 + Loop Output
- Type: Analog Black Burst, Tri-Level
- Impedance: 75Ohms
- Connector, Camera Unit: Internal
- Connector, Base Unit: BNC (x2)
Audio, Camera to Base
- Type: Embedded in Camera's SDI video
- Number of Channels: Max supported by camera
Audio, Base to Camera
- Number of Channels: 2
- Type: Balanced Analog Line-Level, mono
- Level: +4dBu nominal, +24dBu maximum
- Connector, Camera Unit: DB9
- Connector, Base Unit: DB25
Intercom
- Number of Channels: 2
- Interface: 2-Wire or 4-Wire
- Compatibility: RTS, Clear-Com
- Connector, Camera Unit: XLR-5
- Headset MIC Type: Dynamic
- Headset MIC Impedance: 200Ohms nominal
- Connector, Base Unit: DB25
RCP Camera Control (Remote)
- Number of Channels: 1 Per Camera
- Connector, Camera Unit: Internal
- Connector, Base Unit: 6 pin Mini-DIN (x3)
Ethernet
- Number of Channels: 1 Per Camera
- Data Rate: 10/100/1000 Base-T
- Connector, Camera Unit: RJ45 Cat5e
- Connector, Base Unit: RJ45 Cat5e (x3)
Timecode
- Number, Base to Camera: 1 per Camera
- Number, Camera to Base: 1, from Camera # 1 only
- Inputs: Unbalanced, 15Vp-p max
- Outputs: Unbalanced, 3Vp-p
- Connector, Camera Unit: Internal
- Connector, Base Unit: BNC
Tally/GPIO
- Number, Base to Camera: 3 per Camera (Red, Green, Spare)
- Number, Camera to Base: 1 Per Camera
- Inputs: Short to GND or TTL Low to Activate
- Outputs: Relay Contact Closure (30V, 2A max)
- Connector, Camera Unit: DB15
- Connector, Base Unit: DB25
Electro-Optical
- Operating Wavelengths: 1471-1611nm
- Tx Laser Output Power: 0dBm (Class 1 Laser)
- Receiver Sensitivity: -20dBm
- Fiber Compatibility: Single-mode
- Optical Connector Types: opticalCON DUO
Mechanical/Environmental
- Environmental: 0 to 50 deg. C (32 to 122 deg. F), 0 to 95% RH, non-condensing
- Power Input, Base: IEC320, Universal Input, 90-250VAC, 50-60Hz
- Remote Power: Hybrid Fiber Connector
- Local Power: Battery Mount ((Anton Bauer or (Optional) V-Mount))
- Dimensions (H x W x D):
- Camera Unit: 8.2 x 6.7 x 4.2" (20.83 x 17.02 x 10.67cm)
- Base Unit: 3.5 x 19 x 16" (8.89 x 48.26 x 40.64cm) (2RU)
