This JVC FS-900BS2N MultiDyne 2RU Dual Input Fiber Base Station Transceiver with Neutrik opticalCON Connector is the base stations for JVC's unique 2-in-1 fiber optic system designed for JVC's GY-HM890 and GY-HC900 camcorders. The system supports 3G-SDI 1080p/60 camera feeds and returns and takes advantage of the camera's built-in streaming engine for video-over-IP functionality.
Up to two cameras are supported by each base station and redundant power supplies provide up to 150 watts for each camera, as well as prompters and talent monitors. Its three-in-one configuration provides a more cost efficient solution than other multi-camera solutions previously offered by JVC and other manufacturers.
With built-in gigabit Ethernet, the lightweight, 2 RU Base Station also allows video-over-IP, control and advanced configuration. The high quality 1080p video signals are ideal for webcasts, virtual sets and image magnification (I-MAG) applications. The system integrates easily with any studio, mobile truck or portable flypack and connects directly with a facility's switcher, router, intercom and house sync systems.
JVC FS-900BS2N MultiDyne 2RU Dual Input Fiber Base Station Transceiver with Neutrik opticalCON Connector Features:
- Cost-efficient two-camera studio configuration with single base station
- Supports 1080 50/60p 3G-SDI camera feed and returns
- HDMI / SDI feeds for high-quality HD teleprompters
- Gigabit Ethernet for Video-over-IP and web-based RCU
- Dual redundant power supplies
Why not buy this JVC FS-900BS2N MultiDyne 2RU Dual Input Fiber Base Station Transceiver with Neutrik opticalCON Connector today?
JVC FS-900BS2N MultiDyne 2RU Dual Input Fiber Base Station Transceiver with Neutrik opticalCON Connector Specifications:
Digital Video, Camera to Base
- Number of Channels: 1 Per Camera
- Interface: SMPTE ST259, ST292, ST424
- Data Rate: 270Mbps, 1.5Gbps, 3Gbps
- Input/Output Leve: l800mVp-p
- Input/Output Impedance: 75Ohms
- Number of Outputs at Base: 2 Per Camera
Digital Video, Base to Camera
- Number of Channels: 3 Per Camera
- Interface: SMPTE ST259, ST292, ST424, HDMI
- Data Rate: 270Mbps, 1.5Gbps, 3Gbps
- Input/Output Leve: l800mVp-p
- Input/Output Impedance: 75Ohms
- Connectors: BNC, HDMI
Video, Genlock
- Number of Inputs: 1 + Loop Output
- Type: Analog Black Burst, Tri-Level
- Impedance: 75Ohms
- Connector, Camera Unit: Internal
- Connector, Base Unit: BNC (x2)
Audio, Camera to Base
- Type: Embedded in Camera's SDI video
- Number of Channels: Max supported by camera
Audio, Base to Camera
- Number of Channels: 2
- Type: Balanced Analog Line-Level, mono
- Level: +4dBu nominal, +24dBu maximum
- Connector, Camera Unit: DB9
- Connector, Base Unit: DB25
Intercom
- Number of Channels: 2
- Interface: 2-Wire or 4-Wire
- Compatibility: RTS, Clear-Com
- Connector, Camera Unit: XLR-5
- Headset MIC Type: Dynamic
- Headset MIC Impedance: 200Ohms nominal
- Connector, Base Unit: DB25
RCP Camera Control (Remote)
- Number of Channels: 1 Per Camera
- Connector, Camera Unit: Internal
- Connector, Base Unit: 6 pin Mini-DIN (x3)
Ethernet
- Number of Channels: 1 Per Camera
- Data Rate: 10/100/1000 Base-T
- Connector, Camera Unit: RJ45 Cat5e
- Connector, Base Unit: RJ45 Cat5e (x3)
Timecode
- Number, Base to Camera: 1 per Camera
- Number, Camera to Base: 1, from Camera # 1 only
- Inputs: Unbalanced, 15Vp-p max
- Outputs: Unbalanced, 3Vp-p
- Connector, Camera Unit: Internal
- Connector, Base Unit: BNC
Tally/GPIO
- Number, Base to Camera: 3 per Camera (Red, Green, Spare)
- Number, Camera to Base: 1 Per Camera
- Inputs: Short to GND or TTL Low to Activate
- Outputs: Relay Contact Closure (30V, 2A max)
- Connector, Camera Unit: DB15
- Connector, Base Unit: DB25
Electro-Optical
- Operating Wavelengths: 1471-1611nm
- Tx Laser Output Power: 0dBm (Class 1 Laser)
- Receiver Sensitivity: -20dBm
- Fiber Compatibility: Single-mode
- Optical Connector Types: opticalCON DUO
Mechanical/Environmental
- Environmental: 0 to 50 deg. C (32 to 122 deg. F), 0 to 95% RH, non-condensing
- Power Input, Base: IEC320, Universal Input, 90-250VAC, 50-60Hz
- Remote Power: Hybrid Fiber Connector
- Local Power: Battery Mount ((Anton Bauer or (Optional) V-Mount))
- Dimensions (H x W x D):
- Camera Unit: 8.2 x 6.7 x 4.2" (20.83 x 17.02 x 10.67cm)
- Base Unit: 3.5 x 19 x 16" (8.89 x 48.26 x 40.64cm) (2RU)
