This JVC FS-900BS1N Multidyne 3-in-1 Fiber Optic Base Station with opticalCON DUO Connector is part of a fiber optic system designed for the GY-HM890 ProHD Camcorder. The system supports 3G-SDI 1080p/60 camera feeds & returns, and takes advantage of the camera's built-in streaming engine for video-over-IP functionality.
Up to three cameras are supported by the Base Station, and its redundant power supplies provide up to 150W for each camera, as well as prompters and monitors. With built-in gigabit Ethernet, the lightweight, 2 RU Base Station also allows video-over-IP, control, and advanced configuration. The high-quality 1080p video signals are ideal for webcasts, virtual sets, and image magnification (I-MAG) applications. The system integrates easily with any studio, mobile truck, or portable flypack, and connects directly with a facility's switcher, router, intercom, and house sync systems.
JVC FS-900BS1N Multidyne 3-in-1 Fiber Optic Base Station with opticalCON DUO Connector Features:
- Three-camera studio configuration with single base station
- Supports 1080p50/60p 3G-SDI camera feed and returns
- HDMI / SDI feeds for high-quality HD teleprompters
- Gigabit Ethernet for Video-over-IP and web-based RCU
- Dual redundant power supplies
Why not buy this JVC FS-900BS1N Multidyne 3-in-1 Fiber Optic Base Station with opticalCON DUO Connector today?
JVC FS-900BS1N Multidyne 3-in-1 Fiber Optic Base Station with opticalCON DUO Connector Specifications:
- Digital Video:
- Camera to Base:
- Number of Channels: 1 per camera
- Interface: SMPTE ST259, ST292, ST424
- Data Rate: 270 Mbps, 1.5 Gbps, 3 Gbps
- Input/Output Level: 800 mVpp
- Input/Output Impedance: 75 Ohms
- Number of Outputs at Base: 2 per camera
- Base to Camera
- Number of Channels: 3 per camera
- Interface: SMPTE ST259, ST292, ST424, HDMI
- Data Rate: 270 Mbps, 1.5 Gbps, 3 Gbps
- Input/Output Level: 800 mVpp
- Input/Output Impedance: 75 Ohms
- Connectors: BNC, HDMI
- Camera to Base:
- Video:
- Genlock:
- Number of Inputs: 1 + loop output
- Type: Analog black burst, tri-level
- Impedance: 75 Ohms
- Connector for Camera Unit: Internal
- Connector for Base Unit: 2 x BNC
- Audio:
- Camera to Base:
- Type: Embedded in Camera's SDI video
- Number of Channels: Maximum supported by camera
- Base to Camera:
- Number of Channels: 2
- Type: Balanced analog line-level, mono
- Level: +4 dBu nominal, +24 dBu maximum
- Connector for camera unit: DB9
- Connector for base unit: DB25
- Camera to Base:
- Intercom:
- Number of Channels: 2 Interface: 2-wire or 4-wire
- Compatibility: RTS, Clear-Com
- Connector for Camera Unit: XLR-5
- Headset MIC Type: Dynamic
- Headset MIC Impedance: 200 Ohms nominal
- Connector for Base Unit: DB25
- Camera Control:
- RCP Camera Control (remote):
- Number of Channels: 1 per camera
- Connector for Camera Unit: Internal
- Connector for Base Unit: 3 x 6-pin mini-DIN
- Ethernet:
- Number of Channels: 1 per camera
- Data Rate: 10/100/1000 Base-T
- Connector for Camera Unit: RJ45 CAT5e
- Connector for Base Unit: 3 x RJ45 CAT5e
- Timecode:
- Number, Base to Camera: 1 per camera
- Number, Camera to Base: 1, from camera # 1 only
- Inputs: Unbalanced, 15 Vpp maximum
- Outputs: Unbalanced, 3 Vpp
- Connector, Camera Unit: Internal
- Connector, Base Unit: BNC
- Tally / GPIO:
- Number, Base to Camera: 3 per camera (red, green, spare)
- Number, Camera to Base: 1 per camera
- Inputs: Short to GND or TTL low to activate
- Outputs: Relay contact closure (30 V, 2 A maximum)
- Connector, Camera Unit: DB15
- Connector, Base Unit: DB25
- Optical:
- Electro-Optical:
- Operating Wavelengths: 1471 to 1611 nm
- Tx Laser Output Power: 0 dBm (Class 1 Laser)
- Receiver Sensitivity: -20 dBm
- Fiber Compatibility: Single-mode
- Optical Connector Type: opticalCON DUO
- Environmental:
- 32 to 122°F (0 to 50°C)
- 0 to 95% RH, non-condensing
- Power Input: IEC320, universal input, 90 to 250 VAC, 50 to 60 Hz
- Remote Power: Hybrid Fiber Connector
- Dimensions: (2RU): 3.5 x 19 x 16" (8.9 x 48 x 41 cm)
