This Bolin Technology EG40DH Edge DanteAV-H Decoder is a powerful IP decoder capable of receiving a single Dante AV-H video flow over a standard 1GB network and outputting up to 4K60 with embedded Dante audio through HDMI 2.0 and 12G-SDI. It is compatible with all Dante AV-H cameras, Dante Studio software, and Dante audio devices. EG40DH decoder is compatible with:
Bolin Technology EG40DH Edge DanteAV-H Decoder Features:
- Hardware decoder that can receive a Dante AV-H video flow
- Embedded Dante audio through HDMI 2.0 and 12G-SDI simultaneously
- Output up to 4K60, 3840 x 2160 video
- Dante AV-H - when used within Dante AV-H environment
- HEVC - when used with any SoC HEVC IP cameras
- FAST HEVC - when used with Bolin FAST HEVC cameras to gain ultra low latency performance
- Support up to 4K60
- It also functions as a standard IP Decoder and can upscale incoming IP streams up to 2160P.
- Dante AV-H suported with standard HEVC, and FAST HEVC(Ultra-Low-Latency)
- Fully Compatible with Dante Ecosystem hardware and software
- HDMI 2.0 + 12G-SDI video output
- Dual-Output between HDMI and SDI
- Video upscalable max from 720 up to 4K60 (UHD)
- All video with audio embedded
- Audio intercom with frontend device
- On-screen character generator
- Firmware upgrade via IP
- POE+ and 12VDC power input
Why not buy this Bolin Technology EG40DH Edge DanteAV-H Decoder today?
Bolin Technology EG40DH Edge DanteAV-H Decoder Specifications:
| Encoder/Decoder | Decoder only | |
|---|---|---|
| Decoder (Video Output) | HDMI & SDI | |
| Video Codec | Dante AV-H, AVC-H.264 / HEVC-H.265 | |
| Codec Platform | Hardware FPGA FAST HEVC codec | |
| Video Resolutions | 3840 x 2160P @60/59.94/50/30/29.97/25/24/23.98 1920 x 1080P @60/59.94/50/30/29.97/25/24/23.98 1920 x 1080i @60/59.94/50 1280 x 720P @60/59.94/50 | |
| Color Space(HDMI) | 4K60: RGB 8bit, YUV4:4:4 8bit, YUV4:2:2 12bit, 4K30 & below: RGB 8bit/10bit, YUV4:4:4 8bit/10bit, YUV4:2:2 12bit | |
| Audio Formats | 3.5mm Jack, analog audio, stereo (unbalanced); audio intercom, Line out - HDMI audio output | |
| Video Streaming | 1 stream | |
| Control Protocol | - | |
| Latency (Results may vary depending on network configuration and management settings) | A | <4 frame ( <70 ms between encoder and decoder) |
| Bandwidth (Results may vary depending on network configuration and management settings) | A | 4K60 4:2:2/12bit; 20-60Mbps |
| B | 1080p60 4:2:2/12bit; 10-35Mbps | |
| Ecosystem Friendly | A | Dante AV-H, Instant Dante Ecosystem compatibility with existing Dante AV-H enabled products; Unified control of audio and video using Dante tools - Dante Controller |
| B | Video codec is compatible with standard AVC/HEVC, H.264/265 or Dante AV-H to output video without having ultra low latency; Pair with Bolin's Fast HEVC camera or encoder to decode output extremely low latency video. | |
| Video | Highest Resolution | Up to 4K (3840x2160) |
| Highest Frame Rate | Up to 60 | |
| IP Input | Video Codec | Dante AV-H,AVC-H.264 / HEVC-H.265 |
| Video Format | 3840 x 2160P @60/59.94/50/30/29.97/25/24/23.98 1920 x 1080P @120/60/59.94/50/30/29.97/25/24/23.98 1280 x 720P @60/59.94/50 | |
| Frame Rates (Hz) | 23.98, 24, 25, 30, 29.97, 50, 59.94, 60 | |
| Application Protocols | Dante AV-H,RTP, RTSP. MP2TS over UDP, TS over RTP, TS over SRT, HTTP, IGMP v1/v2, DHCP, SSH, 802.1X Authentication | |
| Multi-stream | 1 stream | |
| HDMI Output | Format | HDMI 2.0 |
| Supported Resolutions | 3840 x 2160P @60/59.94/50/30/29.97/25/24/23.98 1920 x 1080P @60/59.94/50/30/29.97/25/24/23.98 1920 x 1080i @60/59.94/50 1280 x 720P @60/59.94/50 | |
| Frame Rates (Hz) | 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 | |
| Color Space | 4K60: RGB 8bit, YUV444 8bit, YUV422 12bit, 4K30 & below: RGB 8bit/10bit, YUV444 8bit/10bit, YUV422 12bit | |
| Upscalling | Yes, upscal from 720P up to FHD, and from FHD to 4K60 resolution | |
| SDI Output | Format | 12G-SDI |
| Supported Resolutions | 3840 x 2160P @60/59.94/50/30/29.97/25/24/23.98 1920 x 1080P @60/59.94/50/30/29.97/25/24/23.98 1920 x 1080i @60/59.94/50 1280 x 720P @60/59.94/50 | |
| Frame Rates (Hz) | 23.98, 24, 25, 29.97, 30, 50, 59.97, 60 | |
| Color Space | YUV422 10bit | |
| Standard | SMPTE 292(1.5Gb/s), SMPTE 424, SMPTE 425-A(3Gb/s), SMPTE 2081, SMPTE 2082-0/1 With SMPTE352 SDI Metadata Supported | |
| Upscalling | Yes, upscal from 720P up to FHD, and from FHD to 4K60 resolution | |
| Audio Transport Formats | Audio Compression | AAC-LC,MPEG-2 |
| Bit Depths | AAC-LC, MPEG-2 (sampling rate: 48KHz/44.1KHz, 24bit, 64-256Kbps selectable) | |
| Audio Transport Formats | Audio S/N Ratio | ≥85dB |
| Audio THD+N | ≤0.05% | |
| Audio Noise (RMS) | ≤-90dB | |
| Intercom | MIC / Headset | Reserved |
| Output Signal Types | Embedded Audio over HDMI | Stereo 2-channel, Dante AV-H ( Audio Flow x 4 Flows / 2 Channels per Flow) |
| Embedded Audio over SDI | Stereo 2-channel | |
| Format | PCM | |
| Line-out | 3.5mm Jack, analog Line-out | |
| Ethernet | Ethernet General A | Standard 1Gbps Ethernet |
| Ethernet General B | Auto-switching, auto-negotiating, auto discovery, full/half duplex | |
| Ethernet with PoE A | IEEE 802.3at compliant 1000BASE-T Ethernet port | |
| Ethernet with PoE B | IEEE 802.3at Type 3 compliant, PoE+ Class 4 | |
| HDMI OUTPUT | HDMI 2.0 Type A connector, female; HDMI digital video/audio output | |
| SDI OUTPUT | 75Ω | |
| Serial Control | RS422 | - |
| Control Protocol | - | |
| PTZ Camera IR Receiver | Front and Back, bidirectional | |
| LED Indicator | Power | Yes, board powered and active (Bolin Logo corner) |
| Codec | Yes, video codec active | |
| Low latency | Yes, light up for low latency mode | |
| System | System status | |
| Error | – | |
| SYNC | – | |
| HDCP | – | |
| Control | Interface | - |
| Protocol | Visca over IP, Bolin Restful API | |
| System Firmware Upgrade | Upgrade via IP web interface or Dante Controller for Dante AV-H | |
| Reset | Yes, long press for 5 seconds to reset | |
| Interface | HDMIx1, SDIx1, 12V DC power portx1, Power switchx1, Reset buttonx1, RJ45x1 (LAN/PoE+), Infrared Receiverx2 (front & back), Line outx1, Intercom Mic inputx1, LED Indicatorx3 | |
| Power | Power Consumption | 18W |
| PoE | PoE+, IEEE 802.3at Type 3 class 4 compliant | |
| Power Adaptor | 12V DC, 2A | |
| Power Adaptor | 12V DC IN has priority over Ethernet PoE. Ethernet PoE will become active a fraction of a second after 12V DC IN is disconnected. | |
| Storage Temperature | -40° to 60° C (-40°F to 140°F) | |
| Operating Temperature | 0° to 50° C (32°F to 122°F) | |
| Humidity | 10% to 90% (non-condensing) | |
| Heat Dissipation | Cooling fan, 3 Level - Automatically adjust the fan speed according to the temperature | |
| Acoustic Noise | NC35 or less, variable with cooling fan speed adjustment | |
| Dimension | 142*150*44mm (LxDxH), 142*150*50.5mm(with feet mats) | |
| Net Weight | 1.05kg (2.31lb) | |
| Chassis | Metal, black finish, heat dissipation surface, fan cooled; vented front and rear | |
| Mounting | Included | HDMI cable secure mount, Base mount |
| Optional | 19" Single-rack mount, 19" Tri-rack mount, Din rail mount, Surface mount | |
| Size of Screw Hole for Tripod | 1/4” | |
| What's Included | Decoder*1, IR Remote Controller, Power Adapter *1 & Power Cord *3 (US, EU, UK), Thank You Card *1 | |
