Wireless iPad, Android Tablet and PC based Software Real Time Video Preview: Along with the other major features like POE, separate audio and more, a key feature is our Wireless iPad, Android Tablet and PC based Software Real Time Video Preview. That means your iPad, Android Tablet or PC using the provided software will show in real time the videos that are on, say, all your DirecTV receivers...again, all of them. If you have 8-DirecTV receivers all set to different channels you'll see 8-different real-time videos, not pictures, but real time video. If it is a DVD playing, you'll see that real time video also. This wireless iPad real time video preview sets us apart from all the other lame ducks who makes you run to the TVs to see what's playing. Only at HDTV Supply can you get this feature. If you need to change the DirecTV channel just go to your DirecTV receivers and change it and you will see it on your iPad as you no longer have to run out to your sports bar floor, factory floor or other areas to see whether it changed or not. The POE HDMI Over IP Matrix system is designed to allow the switching and distribution of up to 50 - Total TXs and RXs and with an Extender Box to unlimited TXs and RXs.
POE Designed: By utilizing POE (Power Over Ethernet) technology both the HDMI audio and video signals and power can be sent to a device via standard CAT6/7/6a/CAT7 cabling. This means you do not need to install a power outlet at the device location and you can use readily available, relatively low cost Ethernet cabling with this POE 6x10 HDMI Over IP Matrix Switcher.
Internal Video Wall Processor of up to a 256-TVs: Not only is this product an HDMI matrix switch it is specifically designed to support multiple video wall configurations. Your iPad, Android Tablet or PC using provided Software is used to create the video walls. Our WolfPack™ POE HDMI Over IP Matrix Switchers uses TCP/IP network technology and has the ability to have a full HD HDMI signal transmitted and distributed to 330 feet with CAT6/5e and 450 feet with CAT6/7. The local and remote units can be connected together for a point-to-point connection, or through VLAN isolation on a managed network switch for a multipoint-to-multipoint configuration.
It supports Drag-N-Drop Video Wall Processing supporting up to 256 TVs (16x16) .
- Example 1: Create a 2x2 Video Wall using 4-TVs with either one large picture or 4-individual pictures at one, or multiple locations.
- Example 2: Create a 3x3 Video Wall using 9-TVs with either one large picture or 9-individual pictures at one, or multiple places.
- Example 3: Create a 4x4 Video Wall using 16-TVs with either one large picture or 16-individual pictures at one, or multiple places...and all easily created by your own iPad!
- Optional 90°, 180° & 270° TV Flip
100ms Seamless HDMI Switching: These HDMI over IP Matrix Switchers deliver nearly instantaneous video switching with full 1080p/60 video at each port. This high-performance engine processes HDMI signals by executing EDID hops and HDCP handshakes simultaneously at both the source input, the display outputs and scales the inputs for the best output resolution. It sets the output clock timing and uses a frame buffer to retain the input signal information for the fastest output.
Separate Audio Outs: These HDMI over IP Matrix Switchers have separate audio outs on the TXs & RXs.
Features that Separates this 6x10 POE WolfPack HDMI Over IP Matrix Switcher from the competition:
- Wireless Real Time Video Preview: See on the iPad what is showing on the TVs, or from the sources, with its iPad, Android Tablet APP and PC based Software.
- Any in, to any out, in any combination
- Includes Drag-N-Drop Video Wall Processing supporting up to a 16x16 (256 TVs)
- All POE design so it doesn't require AC adapters
- Switchable H.264 or H.265 protocol for the best picture
- Automatically sets the IP address
- Extends the signal 330' in & out of the Ethernet switch with CAT6/5e
- iPad & Android Tablet Not Included
Why not buy this POE 6x10 HDMI Over IP Matrix Switcher today?
POE WolfPack HDMI Over IP Matrix Systems Specs:
- Any in, to any out, in any combination
- Transmission distances are up to 100 meters or 330 feet with CAT6/7
- iPad Control
- 1080p video over an 1G Switch
- Supports resolutions up to 1920x1080p 4:4:4
- Supports scalable and flexible input and output matrix configurations
- Field Upgradeable
- Many used in Sports Bars & Clubs
6x10 HDMI Over IP Matrix POE Switcher Configuration:
- 6 - 1080p POE HDMI to IP Transmitters sending to 330 feet
- 10 - 1080p POE HDMI to IP Receivers extending to 330 feet
- POE so no AC Adapters needed
- 1 - Rack mount POE 24-Port 1G IGMP Ethernet switch
- 1 - Wireless iPad Control & Ethernet switch
The HDMI Transmitter Over IP allows you to simultaneously support an HDMI 1.4 Signal (including 1080p video with 5.1 audio) to one or more HDMI video projectors or LCD Panels using one CAT6/7 cable over a standard Ethernet infrastructure.
HDMI Transmitter Over IP Specs:
- Resolutions Supported:
- 640 x 480@60Hz
- 480p@60Hz,
- 576P@50Hz,
- 800 x 600@60Hz,
- 1024 x 768@60Hz,
- 720p@50Hz, 720p@60Hz,
- 1280 x 800@60Hz,
- 1280 x 1024@60Hz,
- 1366 x 768@60Hz,
- 1400 x 1050@60Hz,
- 1440 x 900@60Hz,
- 1680 x 1050@60Hz,
- 1920 x 540@60Hz,
- 1080p@24Hz,
- 1080p@25Hz,
- 1080p@30Hz,
- 1080p@50Hz, 1080p@60Hz
- HDMI 1.3, HDCP 1.4
- POE or can be powered using optional power supply
- No need to do the IP settings as it is plug and play
- WEB GUI control for IP address, video wall, EDID, etc settings
- Supports renaming the sources and displays
- 3-pin audio de-embedded on TX and RX
- EDID preset/learning
- Low latency About 50 ms (Low latency mode) About 250 ms (High quality mode)
- Both Video Wall mode and matrix switch modes
- Supports iPad APP control with preview function
HDMI Transmitter Over IP Set Includes:
- 1 - HDMI Over Ethernet Transmitter unit
- 1 - Optional 12V 1A power adapter
- 1 - User manual
HDMI Transmitter Over IP Specs:
- Input TMDS signal: 1.2 volts (peak-to-peak)
- Input DDC signal: 5 volts (peak-to-peak)
- HDMI Connector: 19 pin type female connector
- RJ-45 Connector
The HDMI Receiver Over IP allows you to simultaneously support an HDMI 1.4 Signal (including 1080p video with 5.1 audio) to one or more HDMI video projectors or LCD Panels using one CAT6/7 cable over a standard Ethernet infrastructure.
HDMI Receiver Over IP Specs:
- Resolutions Supported:
- 640 x 480@60Hz
- 480p@60Hz,
- 576P@50Hz,
- 800 x 600@60Hz,
- 1024 x 768@60Hz,
- 720p@50Hz, 720p@60Hz,
- 1280 x 800@60Hz,
- 1280 x 1024@60Hz,
- 1366 x 768@60Hz,
- 1400 x 1050@60Hz,
- 1440 x 900@60Hz,
- 1680 x 1050@60Hz,
- 1920 x 540@60Hz,
- 1080p@24Hz,
- 1080p@25Hz,
- 1080p@30Hz,
- 1080p@50Hz, 1080p@60Hz
- HDMI 1.3, HDCP 1.4
- POE or can be powered using optional power supply
- No need to do the IP settings s it is plug and play
- WEB GUI control for IP address, video wall, EDID, etc settings
- Supports renaming of the sources and displays
- 3-pin audio de-embedded on TX and RX
- EDID preset/learning
- Low latency About 50 ms (Low latency mode) About 250 ms (High quality mode)
- Both Video Wall mode and matrix switch modes
- Supports iPad APP control with preview function
HDMI Receiver Over IP Set Includes:
- HDMI Over Ethernet Receiver
- Optional 12V 1A power adapter
- User Manual
HDMI Receiver Over IP Specs:
- Input TMDS signal: 1.2 volts (peak-to-peak)
- Input DDC signal: 5 volts (peak-to-peak)
- HDMI Connector: 19 pin type female connector
- RJ-45 Connector
Why not buy this 6x10 HDMI Over IP Matrix Switcher today?
Operation -Windows PC Control Operation Guide
Reasons To Buy an HDTV Supply WolfPack Product
Why not buy this 6x10 HDMI Over IP Matrix Switcher today?
Why not buy this 6x10 HDMI Over IP Matrix Switcher today?
Control
The HDMI Over IP Matrix Switcher has a capability to turn all your TVs OFF & ON via the TVs RS-232 ports. It is contingent on whether your TVs have (1) an RS-232 port and (2) it is compatible with our matrix RS-232 code.This AV over IP system may allow you to control the displays OFF and ON but we will need to make sure that we get the RS232 commands for the displays and also the wiring of the RS232 connection.
Here's what you need to do:
1. Find your TV on the Internet and get us its RS-232 code.
2. See the videos in the above VIDEO TABS which shows how to implement it.
3. See the MANUALS TAB for more about it.
Call us if you have any questions.
DirecTV Controller
100ms Seamless HDMI Switching: These POE HDMI over IP Matrix Switchers deliver nearly instantaneous video switching with full 1080p/60 video at each port. This high-performance engine processes HDMI signals by executing EDID hops and HDCP handshakes simultaneously at both the source input, the display outputs and scales the inputs for the best output resolution. It sets the output clock timing and uses a frame buffer to retain the input signal information for the fastest output.
Separate Embedded Audio In and De-embedded Audio Out: These POE HDMI over IP Matrix Switchers allow you to display video with separate audio coming from another audio source as it supports embedding the audio on the HDMI TXs connector and then de-embedding the audio on the HDMI RXs 3.5mm connector.
The POE HDMI Over IP Matrix system is designed to allow the switching and distribution of up to 50 - Total TXs and RXs and with the Extender Box to unlimited TXs and RXs. With only one low cost CAT6e/7 cable you can readily extend HDMI sources from a laptop, PC, DVD player, game consoles and any other kind of 1080p sources compliant with HDMI and TMDS to distant displays, TV, projectors and monitors including HDMI enabled TV sets or LCD PC monitors up to 330 feet away. With equalization control switch on the receiving unit, users can adjust the equalization strength to the received TMDS signals, and therefore optimize the transmission distance between source and destination.
NOTE: All of these HDMI over IP Matrix Systems, unless otherwise noted, require a dedicated HDMI video system with its own Ethernet switch and not attached to your existing LAN system due to the unknown bandwidth impact on the HDMI video from your network. The design needs to meet these specs:- One Dedicated VLAN for the below devices
- No other network appliances in the VLAN
- Not the same as an existing "Multicast VLAN"
- Unique subnet
- No other network appliances in the subnet
Why not buy this 6x10 HDMI Over IP Matrix Switcher today?
A: We put the products in the heating room for 12-hours for aging and have all the products turned On and the temperature of the heating Room set to 140 degrees. If anything fails we replace the failed unit and start the test over again.
Q: What is the switching time on the HDMI over the IP network?
A: The switching time is about 80 to 100ms.
Q: What is the latency on the HDMI over the IP network?
A: The latency is about 80 to 100ms.
Q: You said this support H.264 and H.265, where do you select this?
A: You can select it from the "HDMIoverIPConsole" software and the default is also H.265.
Can the Ethernet switches be cascaded and still act as a matrix?
A: Yes. The network switches can be cascaded and still act as a large matrix.
Q: Is it a WEB GUI control or PC software
A: It is a PC control software-based system for the setting up the configurations
Q: How do you setup the video wall and can it support a 16x16 video wall 256 TVs?
A: For the video wall set up, it can done it in seconds using the iPad app. The video wall maximum can up to 16x16 with 256 TVs
Q: How do you change the IP and MAC address of the transmitters and receivers?
A: You can set up the IP and MAC on the iPad app or PC control software,but we recommend using the automatic IP and MAC address, so it can support plug and play.
Q: The Transmitters and Receivers both have Audio out on the receiver can the audio be matrixed such as Receiver A sends audio out to Receiver B, if using the audio out?
A: The audio out on both the RX and TX are the corresponding audio with the video so its audio function is only an extract function from the video and is not able to do as an audio matrix.
Q: On the IP control box there are (2) LAN ports, would that be for 2 separate LANs?
A: We will only need to use the LAN 1 for the controlling & settings and for the broadcast version:
- LAN1 (AV/POE): To connect with the network switch use the PC control software to control this system
- LAN2 (C): To connect with the network switch this is used for a 3rd party to use the IP control this system
Q: What is it a distance with POE in and out?
A: With the POE, the input can up to 100m (330 ft) at 1080p@60Hz and the output also is 100m (330 ft)
Q: What is the distance without POE using the AC adapters in and out?
A: It is also the same distance as the POE distance as in and out both are 100m (330 ft)
Q: What type of UTP cable do you recommend?
A: As it's using for the video signal transmission we recommend using the STP 868B cable
Q: Can you use CAT6 - 5E - 6 and 7 and is there a difference in length of cables?
A: We did the tests here with the CAT6/CAT6/Cat6/Cat7 cable and the CAT6 and CAT7 are the best and can reach a distance of 150m with POE
Q: Please give us an explanation of when the large and small streaming resolutions would be used?
A: The highest resolution can up to 1080P@60Hz, the lowest resolution is 680x480@60Hz but that resolution can't support the IP camera decoding
Q: When do you use the control box?
A: There are 2 situations will need to use the control box:
- When using the broadcast version (unlimited TX and RX)
- When needing to use a 3rd party to control this system (IP/ RS232)
What does the PC Configurator do?
A: The PC control software is mainly for the resolutions, CEC, RS232, image rotating and RX/TX IP settings
Q: Does the iPad control require a wireless router?
A: Yes, it will need a WIFI router connected in the same system
Q: In the diagram in the manual it shows the IP control box with only an Internet connection, does a PC plug into it?
A: Yes, the control PC uses a LAN cable connected to the same network switch
Q: You also recommend Managed POE switches, correct?
A: We tested on several POE network switches and so far both of the managed POE or the non-managed POE network are working well. But the managed network switch is more stable and it's fanless which is quieter.
Why not buy this 6x10 HDMI Over IP Matrix Switcher today?
HDTV Supply's WolfPack Family of Matrix Switchers can be created however you wish. Just SCROLL DOWN and fill out the below and press SUBMIT and we will send you a quotation based upon your needs within an hour.
If it doesn't meet your needs just call us right now at 833-WOLFPACK or 833-965-3722 or email us at support@hdtvsupply.com
